Maker Camp is funded in part by the Gordon and Betty Moore Foundation and the generous support of the Members of Make: Community.
TO COMPLETE
WHAT WILL YOU MAKE?
PRINT THESE INSTRUCTIONS
WHAT WILL YOU NEED?
- Large piece of square paper
- Copper tape
- LEDs
- Coin cell battery
STEP 1
Fold Paper
- Fold your paper in half diagonally both ways.
- You should now have an X-shaped crease in your paper.
STEP 2
More Folds
- Now fold your paper in half both ways again, but this time not diagonally.
- Your paper should now be folded into eighths. Repeat steps 1-3, but fold your paper in the opposite direction so that all of the creases go both ways.
STEP 3
Folding
- Fold the top edge of your paper down to the bottom. There should be two diagonal lines on the top half of the folded paper. Fold the right diagonal line back up so that the bottom middle point of the top half now touches the upper right corner.
- Now fold the bottom left corner over so that it is on top of the bottom right corner.
STEP 4
Bit more folding
- Now fold the middle point along the right edge of your paper to the bottom left corner. Your origami should flatten out after this fold.
- Press everything down and smooth all folds.
STEP 5
Even more folding
- Orient your paper so that the crease in the middle is vertical. Fold the left and right corners to the crease.
- Flip your paper over and repeat step nine. Your origami should now resemble a diamond.
STEP 6
Keep folding
- Lift one of the corners that you folded and stick your hand into the cone. Now flatten the cone out.
- Repeat step eleven on all four corners that you folded in steps 9-10.
STEP 7
Fold Fold
- Fold your paper in half so that that the two flattened cones are now pressed together. Flip your paper over and repeat this on the other side.
- Now bend each corner on both sides backwards along the exisiting diagonal creases.
STEP 8
YEAH FOLDING
- If you did all of the folds in step fourteen correctly, your hat should now look like a diamond again.
- Fold the top half of the diamond down, then unfold it. Flip it over and repeat this step on the other side. Be sure to unfold it once more.
STEP 9
done folding
- Now fold the tip of the diamond shape up on all four sides of your hat.
- Open up your futuristic origami hat and try it on!
STEP 10
Add LEDS
- To add LEDs to your hat, pick three of the same color and line them up side by side with their positive legs on the same side. The positive legs are the longer ones.
STEP 11
LEDs
- Cut two pieces of copper tape that are long enough to span across your three LEDs. Tape one across the negative legs and the other across the positive legs.
STEP 12
Working on LEDs
- Fold a piece of copper tape so that it’s inside out and sticky on all sides. Use this to tape the positive side of the coincell battery onto the strip of copper tape that runs along the positive legs of the LEDs.
STEP 13
Copper tape
- Add a piece of copper tape to the negative side of the battery and connect it to the strip of copper tape that runs along the negative legs of the LEDs.
Please Note
Your safety is your own responsibility, including proper use of equipment and safety gear, and determining whether you have adequate skill and experience. Power tools, electricity, and other resources used for these projects are dangerous, unless used properly and with adequate precautions, including safety gear and adult supervision. Some illustrative photos do not depict safety precautions or equipment, in order to show the project steps more clearly. Use of the instructions and suggestions found in Maker Camp is at your own risk. Make Community, LLC, disclaims all responsibility for any resulting damage, injury, or expense.
ALL DONE? SHARE IT!
Share pictures and videos of your cool build! Be sure to use #maketogether or #makercamp
POST YOUR PROJECTSKits and Books From Maker Shed
Make: produces a variety of great products and helpful project tutorials to enhance your making experience.
