Measure and cut 2″ from both ends of
a jumbo craft stick. Measure 1.25″ of the
remaining craft stick and cut it to have one
1.25″ piece and one 0.75″ piece.
Measure and mark 5/8″ away from the
left edge on both the top and bottom edges
of the 1.25″ piece. Connect each mark to the
center of the left edge to form a point.

Cut out the shape that you just made.
It should be a rectangular shape with a
pointed end.
Apply glue to the bottom of one of the
first pieces that you cut out in step one.

Glue the two end pieces together to form
a V shape that has a 2″ opening. The
rounded edges should be at the opening.
Glue the pointed piece on top of the V
shape to make a basket.

Add a small pile of hot glue to the bottom
of the inside of the basket.
Place the 0.75″ piece at an angle on top
of the glue to make a small ramp. This will
guide the ball into the hole if it lands in a
basket.

Now make three more baskets!

Glue one end of the aluminum spacer
to the center of a craft circle. This will be a
spinner on your board.
Measure from the spacer to the end of
the circle. Ours is about 0.25″.

Measure and cut the ends off of two
popsicle sticks so that they are the same
length as the distance measured in step 6.
Glue the four ends to the spacer so that
they are perpendicular to each other.

Make three more spinners!

Measure and cut a 1″ piece from your
3/16″ dowel.
Sand the ends so that they are smooth
and flat.

Glue two jumbo craft sticks together so
that they are about 0.5″ off center.
Glue the 1″ piece of dowel to the end of
one of the craft sticks from step 17.

If you are using our template, cut a
piece of transfer paper to match its size.
Find where you want the center of your
pachinko game to be and drill a 15/64″ hole.

Lay the transfer paper down with the
template on top so that the center hole is
above the hole that you drilled.
Now trace all of the other drill holes.
They are the green circles on the template.

Drill the holes that you traced. Make
sure to sand each hole so that the balls can
freely roll in and out of the holes.
Measure 5/8″ from the edge of one of
the side bumper pieces of wood. Drill a hole
there using the 1/2″ bit.

Glue the bumpers of your game onto
the board. Make sure the hole that you
drilled in one of the bumpers is on the
bottom right when your game is standing
straight up
Remove the clasp from the
embroidery hoop with the hand saw.

Glue a small cube of scrap wood on top
of the center of your bottom bumper.
Bend the embroidery hoop so that it
touches the top, left, and right bumpers.
Mark where there is excess hoop on the
right side of your board.

Cut off the excess hoop and glue your
embroidery hoop down. Glue the bottom
edge to the scrap cube.
Measure and cut the other hoop so
that it connects to the end of the first hoop
on the right side of the board and curves to
the top. Glue it down.

Cut the 1/8″ dowel into four 1″ pieces.
Put the pieces of dowel into the
aluminum spacers on the wheels and mark
how far they go in.

Add a small amount of glue to the four
wheel holes and hammer each dowel piece
in until they reach the marks that you made
in step 17.
Trace the remaing portion of your
template onto the board.

Glue the ball baskets over each ball
hole. Be careful not to obscure the holes
with glue! Lightly sand the plastic
ornament and glue it to the center of your
board. You might have to make the
ornament shorter using the hand saw
Place one spinner on top of each of the
four dowels.

Hammer the nails according to the
template, or make your own design! Just
make sure that the ball cannot get stuck
anywhere.
Hammer the nails closely together
to create the walls that guide the balls into
the baskets. These are represented by solid
curved lines on the template.

Go to part 2 to find out how to
make a ramp, ball tray, stand, and launcher!
We will also be adding lights, sounds, and
an Arduino to our pachinko game.